0
฿0.00
An empty cart
You have no item in your shopping cart
Domnick Thailand · Part of RS Group
Metalworking& FabricationShop Floor Utility Systems
Cutting, grinding, welding, and forming lines all generate the same side effects: airborne metal dust and fume, a need for clean on-demand process gas, and fluid power that has to keep presses and forming equipment cycling without fail. An industrial dust collector and welding fume extractor system, a nitrogen gas generator for metalworking cutting cells, hydraulic hose solutions for press and forming circuits, and an RO membrane for metalworking industry water systems all have to be specified against the actual process, not a generic shop default. Domnick Thailand supplies and commissions all 4 utility categories for fabrication plants across Thailand.
✓ NFPA 652 / 654 Combustible Dust Aware ✓ ISO 8573-1 Air Quality ✓ On-Site High-Purity Gas Generation ✓ Closed-Loop Water Recycling
Fabrication Utility Index
Air, Gas & Particulate Control Categories 01–02
Clean Air FiltrationDust, fume & mist capture at the source
Gas GeneratorsOn-site nitrogen & oxygen for cutting, welding
Fluid Power & Water Systems Categories 03–04
FCG & Motion SystemsHydraulic & pneumatic power for presses
RO MembraneCoolant & process water treatment, reuse
Chat On LINE 4 categories, one supply partner
4 Utility Categories
Air, gas, fluid power & water treatment in one scope
NFPA 652/654 Combustible Dust Awareness
Dust collection specified against ignition risk, not just volume
>99% On-Site Gas Purity Range
Nitrogen & oxygen generation matched to the cutting or welding process
24/7 Continuous Duty
Utilities specified for uninterrupted shop floor operation
Industry Overview
Utility Systems For Metalworking & Fabrication Plants In Thailand
Thailand's metalworking and fabrication sector, spanning laser and plasma cutting, CNC machining, grinding, welding, and sheet metal forming, runs on three utilities that sit outside the machine itself but decide whether it runs cleanly: captured air, supplied gas, and conditioned water. Let any one of them drift and the result shows up as a housekeeping hazard, a rejected weld, or an unplanned line stop.
On the air side, an industrial dust collector and welding fume extractor pull metal dust, grinding fines, and welding smoke away from the operator and the machine before they settle into a combustible dust layer or foul a CNC enclosure. Alongside it, a nitrogen gas generator for metalworking cutting cells supplies the high-purity assist gas that fiber laser and plasma systems need for a clean, oxide-free edge, generated on demand rather than trucked in as cylinders.
Underneath the cutting and welding floor, hydraulic hose solutions and fluid power components keep presses, forming equipment, and material handling systems cycling at rated pressure, while an RO membrane for metalworking industry water system keeps machining coolant and process water clean enough to reuse instead of discharge. Domnick Thailand designs, supplies, and commissions all 4 categories as one scope, matched to the actual cutting, welding, forming, and finishing processes running on the floor.
- Industrial dust collector for metal cutting, grinding & CNC lines
- Welding fume extractor for manual & robotic welding cells
- On-site nitrogen generation for laser cutting & plasma lines
- Oxygen gas generator for fabrication industry welding bays
- Hydraulic hose solutions for press & forming equipment circuits
- Industrial hydraulic cylinders for motion & power transmission
- RO membrane for metalworking industry coolant & wastewater
- RO water treatment for machining coolant reuse & recycling
Utilities By Process Stage
01
Cutting
Laser & plasma assist gas, dust extraction at the bed
02
Forming
Hydraulic & pneumatic power for press and brake cycles
03
Welding
Fume extraction, shielding & purge gas supply
04
Finishing
Grinding dust capture, coolant & wastewater treatment
Why It Matters
The Real Cost Of Treating Shop Utilities As An Afterthought
On a cutting floor, a forming line, or a welding bay, these utilities rarely fail loudly. Three patterns account for most of the housekeeping, quality, and compliance issues fabrication plants run into.
Risk 01
Uncaptured Metal Dust Is A Fire And Explosion Hazard, Not Just A Cleanup Job
Fine metal dust from grinding, cutting, and laser processing can accumulate in ductwork, on overhead surfaces, and inside enclosures, and under the right concentration and ignition source that layer becomes a combustible dust hazard. Combustible dust fundamentals, covered under standards such as NFPA 652 and the equipment-specific NFPA 654, call for collection systems sized and constructed around the hazard class of the dust generated, not simply around airflow volume.
Critical Risk 02
Off-Spec Assist Gas Purity Shows Up As Edge Quality, Not As A Gas Bill
Fiber laser and plasma cutting rely on nitrogen or oxygen assist gas to blow molten metal from the kerf and shield the cut from oxidation. Purity that drifts below the level a given material and thickness requires does not shut the machine down, it shows up later as dross, discoloration, or a dull edge that needs rework, quietly eating into cycle time and consumable cost.
High Risk 03
Degraded Coolant And Process Water Shorten Tool Life Before Anyone Notices
Machining coolant and process water accumulate dissolved solids, oil, and fines over repeated cycles, and once water quality drifts out of range it stops protecting the cutting edge and starts accelerating tool wear, surface finish problems, and bacterial fouling in the sump. Reverse osmosis treatment that is sized to actually cycle that volume, rather than bypassed once it fouls, is what keeps coolant performance consistent batch after batch.
Medium 01 🌬️ Clean Air Filtration
An industrial dust collector and welding fume extractor line, sized for metal cutting, grinding, and CNC dust alongside manual and robotic welding fume.
Explore 02 ⚗️ Gas Generators
A nitrogen gas generator for metalworking cutting cell and on-site oxygen generation system, supplying high-purity assist gas for laser, plasma, and welding processes.
Explore 03 ⚙️ FCG & Motion Systems
Hydraulic hose solutions and industrial hydraulic cylinders, plus fittings, valves, and motion components rated for press, brake, and forming equipment duty.
Explore 04 💧 RO Membrane
An RO membrane for metalworking industry system and RO water treatment for machining coolant, keeping process water clean enough to recycle instead of discharge.
Explore Standards & Compliance
NFPA 652 / 654 Combustible Dust Aware ISO 8573-1 Air Quality ISO 12100 Machine Safety Aware ISO 9001 Quality Thailand Industrial Safety
Utilities Built For The Shop Floor Not Just The Spec Sheet
Our fabrication utility engineers provide system design, equipment specification, and commissioning support for cutting, welding, forming, and finishing lines throughout Thailand.
Get expert guidance when you need it. Our support team is here to provide you with the right solutions.
