0
฿0.00
An empty cart
You have no item in your shopping cart
Domnick Thailand · Part of RS Group
LensManufacturingClean Air And Precision Motion Systems
A lens is judged by what you cannot see: no haze, no water spots, no pits, no coating that lifts at the edge. Behind each of those results is a utility that must stay clean and steady, starting with the compressed air that drives your machines. Domnick Thailand supplies an air compressor for lens manufacturing built for oil-free duty, a compressed air filter for lens manufacturing that catches what is left, compressed air dryers for lens manufacturing that take moisture out, and fluid connectors for lens manufacturing that keep slurry, coolant, and coating fluid where they belong.
ISO 8573-1 Air Quality ISO 14644-1 Cleanroom Aware Oil-Free Air Low Dew Point
01 Oil-Free AirCompressors
02 Clean AirFilters
03 Dry AirDryers
04 Precise MotionFluid and motion
4Connected CategoriesAir, filtration, drying, and fluid and motion in one scope
ISO 8573-1Purity ClassesOil, water, and particles each get a target
-40°CTypical Dew PointReached by desiccant dryers for coating and polishing air
24/7Steady SupplyPressure and quality held through every shift
Industry Overview
Clean, Dry, Steady Utilities For Lens Plants In Thailand
Whether a plant makes spectacle lenses, camera optics, or precision glass components, the route is similar: shape the blank, grind and polish it, clean it, coat it, then inspect and assemble. Compressed air and process fluids touch almost every one of those steps, which is why a compressed air system for optical lens factory use is not the same as a general factory air line.
At the source, an oil free air compressor for lens production removes the biggest risk, oil, before it enters the pipe. Downstream, a cleanroom compressed air filter for lens factory areas and compressed air contamination control in lens production keep particles and vapour away from polished surfaces, while a desiccant air dryer for lens factory lines brings the dew point low enough for coating and cleaning stations.
On the machine side, precision fluid dispensing systems for coatings, slurry and coolant hoses, sealed fittings, and motion components keep each process consistent. Domnick Thailand brings these together as motion and fluid technology solutions for lens industry customers, matched to what runs on your floor.
Air compressor for lens manufacturing Oil free air compressor for lens production Compressed air filter for lens manufacturing Cleanroom compressed air filter for lens factory Compressed air dryers for lens manufacturing Dry compressed air system for lens coating Fluid connectors for lens manufacturing Precision fluid dispensing systems for coatings
Where Utilities Touch The Lens
01
Shape And Cut
Pneumatic clamping and tooling, with coolant circuits protecting the blank.
02
Grind And Polish
Stable air for machine drives and air-supported axes, plus slurry and coolant lines.
03
Clean And Dry
Blow-off and drying with air that adds no oil, water, or dust.
04
Coat
Dry air for pneumatic valves, plus chemical-resistant tubing and fittings.
05
Inspect And Assemble
Pneumatic grippers, vacuum handling, and precise motion on assembly lines.
Why It Matters
What Poor Utilities Look Like On The Lens
Problems in compressed air and fluid systems rarely trigger an alarm. They arrive later as rejected lenses. Three patterns cause most of them.
01
Oil Film Weakens Coatings Before They Are Applied
Oil aerosol and vapour from an ordinary compressor can carry into blow-off and cleaning air and leave a thin film on the lens surface. Even a very light film can stop an anti-reflective or hard coat from bonding well. An oil free air compressor for lens production, backed by a high-efficiency filter, removes the source instead of chasing the effect.
On the lensHaze, smears, coating that peels
02
Moisture In The Air Line Leaves Marks And Corrodes Parts
Warm, humid air cools inside the piping and drops water. That water spots a cleaned lens, rusts pneumatic parts, and encourages microbial growth. Compressed air dryers for lens manufacturing hold the dew point below the coldest point in the line, so nothing condenses where it should not.
On the lensWater spots, fogging, stains
03
Particles And Unstable Pressure Disturb Precise Processes
Fine dust blown onto a polished surface can scratch it, and pressure that swings can upset air-supported axes and pneumatic fixtures. A compressed air system for optical lens factory duty uses filtration at the point of use and a steady supply upstream, so each cycle starts from the same conditions.
On the lensScratches, pits, form error, rework
Solutions Index
4 Categories For Lens Manufacturing
One connected scope, from the air at the compressor to the fluid at the machine, specified for the way lenses are actually made. Not sure where to start? Chat with an engineer on LINE.
01
Air Compressor
An air compressor for lens manufacturing that delivers oil-free, stable air from the very first stage. A compressed air system for optical lens factory projects starts here, because everything downstream is only as clean as the air it receives.
Explore02
Compressed Air Filter
A compressed air filter for lens manufacturing that removes particles, oil aerosol, and vapour, including cleanroom compressed air filter for lens factory grades, for full compressed air contamination control in lens production.
Explore03
Compressed Air Dryers
Compressed air dryers for lens manufacturing, including a desiccant air dryer for lens factory lines, and a dry compressed air system for lens coating that hold a low, steady dew point.
Explore04
FCG & Motion Systems
Fluid connectors for lens manufacturing, hoses, seals, and precision fluid dispensing systems for coatings, with precise motion components that complete the circuit. Motion and fluid technology solutions for lens industry machines, supplied as one package.
Explore Standards & Compliance
ISO 8573-1 Compressed Air Purity ISO 14644-1 Cleanroom Aware ISO 9211 Optical Coatings Aware ISO 9001 Quality Thailand Industrial Safety
Clear Lenses Start With Clean Utilities
Our engineers review your compressed air, filtration, drying, and fluid systems against the lens process you run, then specify and commission them as one connected scope across Thailand.
Get expert guidance when you need it. Our support team is here to provide you with the right solutions.
